5-40 UNC tap drill size and thread dimensions
5-40 UNC has a major diameter of 3.175 mm and a pitch of 40 threads per inch (0.6350 mm). Every other dimension below follows from those two numbers and the 60-degree thread form.
- Clearance hole
- 3.429
- Pitch diameter
- 2.7626
- Minor diameter of the nut thread
- 2.4876
- Minor diameter of the bolt thread
- 2.3959
- Tensile stress area
- 5.225 mm2
- Breaking load at that tensile strength
- 4180
- The old "diameter minus pitch" drill
- 2.540
- Engagement that rule actually gives
- 92.4 %
- Threads engaged over that length
- 7.56
- Equivalent threads per inch
- 40.000
Show the working
- Thread engagement = 75
- Clearance hole allowance = 8
- Length of engagement = 4.8
- Material tensile strength = 800
- major = 3.175 = 3.175
- p = 0.635 = 0.635
- h = 0.635 * 0.8660254037844386 = 0.549 926
- Tap drill = 3.175 - 75/100 * 1.082532 * 0.635 = 2.659 44
- The old "diameter minus pitch" drill = 3.175 - 0.635 = 2.54
- Engagement that rule actually gives = 100 / 1.082532 = 92.376
- Pitch diameter = 3.175 - 0.649519 * 0.635 = 2.762 56
- Minor diameter of the nut thread = 3.175 - 1.082532 * 0.635 = 2.487 59
- Minor diameter of the bolt thread = 3.175 - 1.226869 * 0.635 = 2.395 94
- Tensile stress area = pi/4 * (3.175 - 0.938194 * 0.635)^2 = 5.224 87
- Clearance hole = 3.175 * (1 + 8/100) = 3.429
- Breaking load at that tensile strength = 5.224 87 * 800 = 4179.9
- shear_area = pi * 2.487 59 * 4.8 * (0.5 + 0.57735 * (2.762 56 - 2.487 59)/0.635) = 28.134
- Threads engaged over that length = 0.635 > 0 ? 4.8 / 0.635 : 0 = 7.559 06
- Equivalent threads per inch = 0.635 > 0 ? 25.4 / 0.635 : 0 = 40
Values are shown to six significant figures here; the arithmetic itself runs on exact fractions and is only rounded where a number is printed.
Scenarios & local history
Compare a saved scenario
Recent calculations
The formula
- tap drill = D - (engagement / 100) x 1.082532 x P
- pitch diameter = D - 0.649519 P
- internal minor diameter = D - 1.082532 P
- tensile stress area = (pi/4)(D - 0.938194 P)^2
The familiar "drill equals diameter minus pitch" rule actually produces about 92% thread engagement, not 75%. Past roughly 75% the extra holding power is negligible and the tapping torque rises sharply, which is why 75% or even 65% is the shop standard.
The tensile stress area formula is the ISO 898-1 definition, based on the mean of the pitch and minor diameters.
Cut a clearance hole rather than a close fit unless the joint is dowelled: thread clearance is what lets parts line up.
5-40 UNC at common engagements
| Engagement | Tap drill (mm) | Tap drill (in) |
|---|---|---|
| 65% | 2.728 | 0.1074 |
| 70% | 2.694 | 0.1061 |
| 75% | 2.659 | 0.1047 |
| 80% | 2.625 | 0.1033 |
| 85% | 2.591 | 0.1020 |
| 90% | 2.556 | 0.1006 |
Pick the nearest drill above the figure, never below it.
Frequently asked
What drill size do I need for 5-40 UNC?
2.66 mm (0.1047 in) for 75% thread engagement. The traditional rule gives 2.54 mm, which is a tighter and harder-tapping hole.
What is the pitch of 5-40 UNC?
40 threads per inch (0.6350 mm).
Where the numbers come from
- Thread geometry follows the ISO 68-1 basic profile shared by ISO metric and Unified inch threads; the stress-area definition is from ISO 898-1.