7/16-20 UNF tap drill size and thread dimensions
7/16-20 UNF has a major diameter of 11.112 mm and a pitch of 20 threads per inch (1.2700 mm). Every other dimension below follows from those two numbers and the 60-degree thread form.
- Clearance hole
- 12.001
- Pitch diameter
- 10.2876
- Minor diameter of the nut thread
- 9.7377
- Minor diameter of the bolt thread
- 9.5544
- Tensile stress area
- 77.304 mm2
- Breaking load at that tensile strength
- 61 843
- The old "diameter minus pitch" drill
- 9.842
- Engagement that rule actually gives
- 92.4 %
- Threads engaged over that length
- 13.15
- Equivalent threads per inch
- 20.000
Show the working
- Thread engagement = 75
- Clearance hole allowance = 8
- Length of engagement = 16.7
- Material tensile strength = 800
- major = 11.112499999999999 = 11.1125
- p = 1.27 = 1.27
- h = 1.27 * 0.8660254037844386 = 1.099 85
- Tap drill = 11.1125 - 75/100 * 1.082532 * 1.27 = 10.0814
- The old "diameter minus pitch" drill = 11.1125 - 1.27 = 9.8425
- Engagement that rule actually gives = 100 / 1.082532 = 92.376
- Pitch diameter = 11.1125 - 0.649519 * 1.27 = 10.2876
- Minor diameter of the nut thread = 11.1125 - 1.082532 * 1.27 = 9.737 68
- Minor diameter of the bolt thread = 11.1125 - 1.226869 * 1.27 = 9.554 38
- Tensile stress area = pi/4 * (11.1125 - 0.938194 * 1.27)^2 = 77.3037
- Clearance hole = 11.1125 * (1 + 8/100) = 12.0015
- Breaking load at that tensile strength = 77.3037 * 800 = 61 843
- shear_area = pi * 9.737 68 * 16.7 * (0.5 + 0.57735 * (10.2876 - 9.737 68)/1.27) = 383.163
- Threads engaged over that length = 1.27 > 0 ? 16.7 / 1.27 : 0 = 13.1496
- Equivalent threads per inch = 1.27 > 0 ? 25.4 / 1.27 : 0 = 20
Values are shown to six significant figures here; the arithmetic itself runs on exact fractions and is only rounded where a number is printed.
Scenarios & local history
Compare a saved scenario
Recent calculations
The formula
- tap drill = D - (engagement / 100) x 1.082532 x P
- pitch diameter = D - 0.649519 P
- internal minor diameter = D - 1.082532 P
- tensile stress area = (pi/4)(D - 0.938194 P)^2
The familiar "drill equals diameter minus pitch" rule actually produces about 92% thread engagement, not 75%. Past roughly 75% the extra holding power is negligible and the tapping torque rises sharply, which is why 75% or even 65% is the shop standard.
The tensile stress area formula is the ISO 898-1 definition, based on the mean of the pitch and minor diameters.
Cut a clearance hole rather than a close fit unless the joint is dowelled: thread clearance is what lets parts line up.
7/16-20 UNF at common engagements
| Engagement | Tap drill (mm) | Tap drill (in) |
|---|---|---|
| 65% | 10.219 | 0.4023 |
| 70% | 10.150 | 0.3996 |
| 75% | 10.081 | 0.3969 |
| 80% | 10.013 | 0.3942 |
| 85% | 9.944 | 0.3915 |
| 90% | 9.875 | 0.3888 |
Pick the nearest drill above the figure, never below it.
Frequently asked
What drill size do I need for 7/16-20 UNF?
10.08 mm (0.3969 in) for 75% thread engagement. The traditional rule gives 9.84 mm, which is a tighter and harder-tapping hole.
What is the pitch of 7/16-20 UNF?
20 threads per inch (1.2700 mm).
Where the numbers come from
- Thread geometry follows the ISO 68-1 basic profile shared by ISO metric and Unified inch threads; the stress-area definition is from ISO 898-1.